Internal Issue Addressing Videos (CNCTools.co.za)

Machine: Silkscreen
SKU: SP-2540
Automatic Flat 250×400mm Silkscreen Printer, 300×500mm Working Table, 220V 50W with Maximum 1000 Prints/Hour Printing Speed. 4-6 Bar Compressed Air Needed

00:00:00:09 - 00:00:52:14
Unknown
Let me once again adjust the 4060 flat printing machine to print the anti-counterfeiting fabric and leather as an automatic five-star. Let’s first determine the height. First, let’s lower the capital to international level eight. First of all, we just need to leave a gap of 3 to 5 mm between the product and the product. Look at it now with your hands, and now this is for adjusting the height. Now it is constantly testing the distance from the screen to the product with your hands. Because the fabric is relatively thin, it is OK if we hit you directly. Ah, it’s not easy. You must remember that you must not let the bottom of this screen version stick to the surface of this product.

00:00:52:14 - 00:01:15:06
Unknown
To put it bluntly, everyone must believe what I said, and our left and right strokes are adjusted through this sensor. Now let’s move this brush on the right a little bit further over there. Now at this distance after brushing, the ink will flow to the pattern a little bit. Let’s try to make this stroke wider.

00:01:15:18 - 00:01:56:09
Unknown
Some people also say that the larger the stroke, the slower the printing speed. This is not necessarily true. If we want to make sports better, then we must make this blog bigger, or we can make it a little faster. Then this thing you found, now I buy this iron piece, this knife is just right, according to the surface of this plate, this is just a cover and one function, so it doesn’t need to be added too much, and then we can use this brush to make it Go down 3 to 5 mm.

00:01:56:09 - 00:02:24:12
Unknown
Go in one by one, and now let’s adjust this pressure on the knife on the right. Now we have the same pressure on the knife. We set it down to 3 to 5 mm. Because this product happens to have a gap of 3 to 5 mm from the fabric, we also adjust its height to 3 to 5 mm. There is a gap. After we are naughty like this, we can start pouring the mold immediately.

00:02:24:12 - 00:02:52:21
Unknown
Let’s use this on other materials first to see the effect, and then we will ship it to this product, so that this product will not be wasted. Today it’s me, and I’ll try some humour first. Many people say that this master’s humorous approach is wrong. Today, a master with more than 20 years of experience will show you this humorous method. Is it right today?

00:02:52:23 - 00:03:52:21
Unknown
First of all, we are going to be semi-automatic now, and then we will take a look at the impressions. In order not to waste this material, we first print it on the acrylic plate. Today we are printing this fabric. The pressure we used first was not enough. Now we are adding a little more pressure to both sides. Now we will add another one that feels like it should be better. It’s almost done. You can add a little more. Let’s reduce the overall pressure. You’re doing quite well with the ink. Now let’s give you two laps. It should be coming out now, or it’s still a little bit close. Let’s go down. Add a little more pressure, now this toy feels a little bit higher, let’s brush this pressure out again, and then we’re on top of this, and we’re going to

00:03:52:21 - 00:04:19:02
Unknown
Take a look again. Now I feel that the scraping on the board is very good. The pressure is uneven after all. Then we adjust the pressure and increase the pressure inside. Let’s try it again. Let’s see. You can see the ink above us. I feel that it has been scraped very clean now. It must be said to be very good. You can take a look at the current effect. I said it is very good.

00:04:20:06 - 00:04:50:23
Unknown
Okay, we are stamping, we can use this product right away, then we will put in the materials and do it. Next, let’s try another one. Now we have this PVC acrylic printed glass. It seems that the effect is quite good, very good. PVC acrylic lens camera glass camera sign screen printing machine can print very clearly with such small fonts.

00:04:51:01 - 00:05:15:04
Unknown
Okay, let’s take another one. We can wait. We can wipe it down later and then print it directly on this product. It’s great. Well, with such small characters, you can see that these QR codes are hard, which is quite good.

Machines, Consumables and Parts Available from buythis.co.za/

For more info on Advanced Machinery visit am.co.za/

Chat with us by sending “hi” on Whatsapp to 060 600 6000.

Advanced Machinery,Machines,South Africa,AM.CO.ZA,Silkscreen,Printer,Adjustment